The Camaro Club (UK)

Online Community for all Camaro Owners and enthusiasts
It is currently Thu Nov 14, 2024 5:32 pm

All times are UTC




Post new topic Reply to topic  [13 posts ]  Go to page12Next
Author Message
 Post subject: Oil sender
PostPosted:Fri Mar 11, 2011 6:41 pm 
Offline
Big Block
User avatar

Joined:Tue Feb 23, 2010 12:40 pm
Posts:3245
Car Details:'79 Camaro, 350 V8
Location:South Bucks
Hoping to get some installation advice on the oil sender please.

The stock one was creating a short plus the new autometer gauge came with a new sender so i wanted to install that. problem is, it's way too wide and its pushing against the intake manifold so i can't get it close to threading in it.

I came up with the solution of buying a male:male pipe fitting and attaching a female:female to this is it would life it just high enough to clear the intake manifold. spent 3.5 hours looking fora pipe fitting that was 1/8 inch, could only find as small as 1/4 in stores. found a place on ebay, next day delivery took 4 days, awesome, just went out and tried it but the thread isn't right. wtf?! when i place the female:female adapter on the new or old sender, it catches the thread but about 1/4 of a turn later it just gets jammed. i tried the male:male fitting and it goes all the way through the female:female thread so i'm clueless here. anyone had this type of issue and knows how to overcome? I'm just sayin, now i'm beginning to understand why people sell project cars as unfinished :x

Pics below as always!
Thanks for any help you can give!

The solution to raise the sender for clearance:
Attachment:
IMG_0454.JPG
IMG_0454.JPG [750.79KiB |Viewed 1474 times ]
The new sender is on top. clearly a like for like swap out :roll:
Attachment:
IMG_0456.JPG
IMG_0456.JPG [665.35KiB |Viewed 1467 times ]

_________________
How to post pics: When writing a message, scroll down and use the "attach file" option. Where possible, a photo sharing service can be used such as Flickr, Imgur etc. The image location (usually ending in .jpg) can be copy and pasted between the ][ brackets that appear when you click the 'Img' button (you can find this button at the top of the message box).

How to post youtube vids: Click on the 'youtubeHD' button at the top of the message box and in the middle of the ][ brackets that just appeared, copy and paste everything from the youtube web address that appears after the = sign i.e if this is the url: https://www.youtube.com/watch?v=K2cNqaPSHv0 just copy "K2cNqaPSHv0").


Top
   

Oil sender

Sponsor

Sponsor
 

 Post subject: Re: Oil sender
PostPosted:Fri Mar 11, 2011 7:49 pm 
Offline
Big Block

Joined:Mon Dec 22, 2008 10:53 am
Posts:306
Car Details:'68 Camaro
'89 Golf Rallye
'97 Golf GTi (Daily)
Location:SE London/Kent
Gonna get all technical now, but probably I'm talking a load of bull's dangly bits..... :lol: :lol:

different thread pitch? or AN vs NPT?

_________________
'68 Camaro


Top
   
 Post subject: Re: Oil sender
PostPosted:Fri Mar 11, 2011 8:14 pm 
Offline
Big Block
User avatar

Joined:Tue Feb 23, 2010 12:40 pm
Posts:3245
Car Details:'79 Camaro, 350 V8
Location:South Bucks
haha, i think ur right Mark!

been searching for a while, came across this form autometers site:

http://www.autometer.com/techinfo_newsa ... pg=1&aid=9

states that their sender uses 1/8 NPT. the ones i brought were 1/8 BSPT. :wtf:

Naturally i'm having a tough time finding someone that sells NPT fittings. found 2 plumbing stores in slough trading estate so will pop in in the morning and god help anyone around me if they don't stock them.

Fingers crossed this solution will do the trick!

As a side note, it's all well and good knowing what the oil pressure is, but is there anything that states what it should be? would this differ for each engine? As you can see, i'm not mechanically inclined ;)

Cheers!

_________________
How to post pics: When writing a message, scroll down and use the "attach file" option. Where possible, a photo sharing service can be used such as Flickr, Imgur etc. The image location (usually ending in .jpg) can be copy and pasted between the ][ brackets that appear when you click the 'Img' button (you can find this button at the top of the message box).

How to post youtube vids: Click on the 'youtubeHD' button at the top of the message box and in the middle of the ][ brackets that just appeared, copy and paste everything from the youtube web address that appears after the = sign i.e if this is the url: https://www.youtube.com/watch?v=K2cNqaPSHv0 just copy "K2cNqaPSHv0").


Top
   
 Post subject: Re: Oil sender
PostPosted:Fri Mar 11, 2011 8:52 pm 
Offline
Big Block

Joined:Mon Dec 22, 2008 10:53 am
Posts:306
Car Details:'68 Camaro
'89 Golf Rallye
'97 Golf GTi (Daily)
Location:SE London/Kent
oh dear :lol: , i didn't want to be right! Good luck tomorrow!

At a wild guess, between 40-60psi - at operating temp, may differ depending on oil used and oil pump (high pressure pump?) I'm sure someone on the forum will give you a more accurate answer :thumbup:

_________________
'68 Camaro


Top
   
 Post subject: Re: Oil sender
PostPosted:Sun Mar 20, 2011 8:29 pm 
Offline
Big Block
User avatar

Joined:Tue Feb 23, 2010 12:40 pm
Posts:3245
Car Details:'79 Camaro, 350 V8
Location:South Bucks
Cheers Mark, glad you're right, rather that than playing more and more guess work :lol:

Finding it very difficult to find a UK supplier that does NPT fittings. Managed to track down a company in silverstone that do all sort of lines and fittings so they are going to make me up a braided hose line to have a remote pressure sender.

I believe that the oil pump is standard, we will soon find out :) The autometer sender says max 100 psi so i should imagine you're correct in 40-60 being the sweet spot.

Will let you know how i get on.

Cheers!

Ray

_________________
How to post pics: When writing a message, scroll down and use the "attach file" option. Where possible, a photo sharing service can be used such as Flickr, Imgur etc. The image location (usually ending in .jpg) can be copy and pasted between the ][ brackets that appear when you click the 'Img' button (you can find this button at the top of the message box).

How to post youtube vids: Click on the 'youtubeHD' button at the top of the message box and in the middle of the ][ brackets that just appeared, copy and paste everything from the youtube web address that appears after the = sign i.e if this is the url: https://www.youtube.com/watch?v=K2cNqaPSHv0 just copy "K2cNqaPSHv0").


Top
   
 Post subject: Re: Oil sender
PostPosted:Mon Mar 21, 2011 9:39 am 
Offline
Big Block
User avatar

Joined:Mon Feb 09, 2009 12:41 pm
Posts:2451
Quote:
Cheers Mark, glad you're right, rather that than playing more and more guess work :lol:

Finding it very difficult to find a UK supplier that does NPT fittings. Managed to track down a company in silverstone that do all sort of lines and fittings so they are going to make me up a braided hose line to have a remote pressure sender.

I believe that the oil pump is standard, we will soon find out :) The autometer sender says max 100 psi so i should imagine you're correct in 40-60 being the sweet spot.

Will let you know how i get on.

Cheers!

Ray
Hi Ray, as Mark said, it depends to some extent on what pump & oil you're running. A general rule of thumb is 10 psi per 1000rpm. If the oil pump is standard then it's not unusual for them to run at 30-40 psi & possibly drop down to 15 psi on tickover.

What oil are you using?? The reason I ask this is that most oils nowadays have a very low content of zinc dithiophosphate (ZDDP). The zinc actually lubricated the cam & valvetrain on flat tappet cams. It's essential to have ZDDP in older flat tappet engines & especially so, when running in a new cam.

I use Valvoline Racing VR1 20W-50 motor oil. I always put a 12 fl oz bottle of Comp Cams engine break in additive into the 5 litres of oil, give it a really good shake & then use it in all subsequent oil top ups & oil changes, this way you're always keeping the engine fully protected.

here's a link

http://www.compcams.com/WhatsNew/NewsDe ... =833414428

hope that helps

cheers...Nige

_________________
Too much power...not enough hands!!


Top
   
 Post subject: Re: Oil sender
PostPosted:Tue Mar 22, 2011 1:17 pm 
Offline
Big Block
User avatar

Joined:Tue Feb 23, 2010 12:40 pm
Posts:3245
Car Details:'79 Camaro, 350 V8
Location:South Bucks
Thanks Nige,

That's a good rule of thumb basing 10 psi on 1,000 rpm :) Mechanically i have a LOT to learn still so apologies for my lack of knwo how :oops:

The new pipe should be arrivbing in a couple of days so will be able to test the theory :thumbup:

I'm not sure what oil is in there, there was a leftover bottle in the garage which the owner must have you used after the engine rebuild (he gave me lots of spares and extras from his garage, felt bad! he even had an original hood but we had no space to put it to take it home in so it went to the scrappy :cry: ... basically his now ex wife siad whatever is left on sunday morning is going to the scrap so we filled the camaro and my mates car with everything we could). Anyway the oil bottle is not a known name and just had 10w40 on it. I use Castrol magnatec 10w40 in the clio and was thinking of using the same for the camaro but i will try and find some of the ZDDP Valvoline you mentioned. Would have never thought that, thanks :) Even though it's only done 600 miles since the rebuild i will change the oil for good measure before i take it out.

Cheers again!

Ray

_________________
How to post pics: When writing a message, scroll down and use the "attach file" option. Where possible, a photo sharing service can be used such as Flickr, Imgur etc. The image location (usually ending in .jpg) can be copy and pasted between the ][ brackets that appear when you click the 'Img' button (you can find this button at the top of the message box).

How to post youtube vids: Click on the 'youtubeHD' button at the top of the message box and in the middle of the ][ brackets that just appeared, copy and paste everything from the youtube web address that appears after the = sign i.e if this is the url: https://www.youtube.com/watch?v=K2cNqaPSHv0 just copy "K2cNqaPSHv0").


Top
   
 Post subject: Re: Oil sender
PostPosted:Tue Mar 22, 2011 6:14 pm 
Offline
Big Block
User avatar

Joined:Thu Jul 10, 2008 10:41 am
Posts:827
Car Details:1968 Camaro Racing Car "Butch"
1968 Camaro Convertible 327"Camilla"
1979 AMC CJ7 Jeep 360V8
1980 BMW E21 Alpina B6 2.8
1991 BMW E30 HartgeH26
1958 as yet unrevealed sportsracer with chevV8
Location:Isle of Man and Inverness
When I had a wet sump we had an accumulator fitted that dumped the oil into the top of the engine ;
a upon start-up and
b when oil pressure dropped below 20 psi

When the oil is very hot ie over 200f the oil pressure drops- and we often had the accumulator doing its thing on hard right hand turns whilst racing in South Africa. There is a banked turn in Capetown and a hard about at Zwartkops. So in extremis 20 psi when hot see below:
Oil pressure: 25-30 min at idle
75-95 max at WOT cold
(WOT= wide open throttle)
Kenny Coleman agrees with the Valvoline Racing oils route- we only use Valvoline Racing 20/50 or Kendall 20/50 GT1
Have you tried Real Steel for those threads?

_________________
Kind Regards
TopCat
Secretary
Classic Camaro Club
Member of The Association of American Car Clubs UK
Email :tboles@strathnoon.co.uk Websites: http://www.classiccamaroclubuk.com and:
http://www.youtube.com/watch?v=IdhLJtR_ZY4


Top
   
 Post subject: Re: Oil sender
PostPosted:Tue Mar 22, 2011 11:10 pm 
Offline
Big Block

Joined:Mon Oct 05, 2009 10:00 pm
Posts:122
Car Details:tube framed 68 camaro
Location:WHITEHAVEN, CUMBRIA
my smallblock runs at 80 psi on startup, when the motor is hot,this drops to 20 psi idling in gear, and when driving, stays at around 35/40 psi.
as long as you're getting a minimum of 15 psi plus, under ALL conditions, i shouldnt worry too much (i've seen almost new jags idling at 14 psi when hot!)

_________________
I KNOW WHERE YOU LIVE......

Image

I'M JUST TOO DAMNED TIRED TO BOTHER CHASING YOU !


Top
   
 Post subject: Re: Oil sender
PostPosted:Wed Mar 23, 2011 9:17 am 
Offline
Big Block
User avatar

Joined:Mon Feb 09, 2009 12:41 pm
Posts:2451
Quote:
i will try and find some of the ZDDP Valvoline you mentioned. Would have never thought that, thanks :) Even though it's only done 600 miles since the rebuild i will change the oil for good measure before i take it out.

Cheers again!

Ray

Hi Ray, it's not ZDDP Valvoline, but Valvoline Racing VR1 20W-50 motor oil. The 12 fl oz bottle of Comp Cams engine break in additive is what contains the extra ZDDP. Mix them together as in my previous post & you're engine will be protected. Both are available from Real Steel hth

Real Steels number

01895 440505

cheers...Nige

_________________
Too much power...not enough hands!!


Top
   
Display posts from previous: Sort by 
Post new topic Reply to topic  [13 posts ]  Go to page12Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 104 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Limited