The Camaro Club (UK)

Online Community for all Camaro Owners and enthusiasts
It is currently Fri Nov 01, 2024 7:35 am

All times are UTC




Post new topic Reply to topic  [12 posts ]  Go to page12Next
Author Message
 Post subject: rolling the arches
PostPosted:Mon May 20, 2013 2:59 pm 
Offline
Big Block
User avatar

Joined:Wed Aug 01, 2012 10:49 pm
Posts:500
Car Details:a car thats older than the c*** that drives it....
Location:n london/ herts
getting conflicting advice but can i bend up the rear lips by heating up and tapping with a bit of wood and a hammer ???????


Top
   

rolling the arches

Sponsor

Sponsor
 

 Post subject: Re: rolling the arches
PostPosted:Mon May 20, 2013 3:26 pm 
Offline
Big Block
User avatar

Joined:Mon Feb 09, 2009 12:41 pm
Posts:2451
Yes & No, how's that for an answer? :lol: The reason you would want to warm the arch up is to help soften the paint to stop it cracking, not to soften the metal. Try to soften the metal & the paint will blister. I'd mask up the paintwork with a few layers of masking tape, just in case you miss the target, & then gently tap the arch from end to end with a panel hammer, repeating the process until the arch is where you want it.. Alternatively, use a bit of flat soft wood between the hammer & the arch & again, gently, gently tap it into place. I've done this a few times on upmarket cars & can't emphasize on doing it a bit at a time. If you take your time it should be ok, unless there's filler in the arch in which case it will crack. Be prepared for the fact that you might have to repair the 1/4's & paint the arch though. You're better off getting the right size back spacing on the wheels & fitting the right tyres tbh
You can buy a tool for doing this, but it's finding someone that'll lend it to you.hth.
cheers
Nige

_________________
Too much power...not enough hands!!


Top
   
 Post subject: Re: rolling the arches
PostPosted:Mon May 20, 2013 6:46 pm 
Offline
Big Block
User avatar

Joined:Wed Aug 01, 2012 10:49 pm
Posts:500
Car Details:a car thats older than the c*** that drives it....
Location:n london/ herts
cheers Nige..... we did a bit then the paint started to crack (stevie wonder and ray charles painted the car back in the states after 10 cans of super tenants each and the paint chips if you sneeze on it)
on the wheels I measured from the rear hubs back to the shock mounts and is 4"3/4 so is 4"1/2 back spacing ok ???? want to put 18"x8" on the rear and have 14"x8" with 3"3/8 b/s on at the moment ...can i get 255 on a 8" rim ok ????
Attachment:
2012-10-04_11-08-42_423.jpg
2012-10-04_11-08-42_423.jpg [42.24KiB |Viewed 982 times ]
Attachment:
DSCF1065.jpg
DSCF1065.jpg [72.18KiB |Viewed 982 times ]
probably go for these as they are the only ones available in 17" and 18" that are cheapish


Top
   
 Post subject: Re: rolling the arches
PostPosted:Mon May 20, 2013 7:25 pm 
Offline
Big Block

Joined:Sun Jan 01, 2012 5:00 pm
Posts:342
Car Details:Couple of '70 Mustangs
Always a problem when trying to fit wheels that are just too big. Been there, done that many times as Nigel can attest. Now I only use wheels/tyres that fit and work and guess what? ALL the problems have disappeared!
I still have to fight with customers who want more tyre/wheel than their car can take, can't be done.
Cheers, Martin

_________________
*WARNING* The following actions have generated error codes.


Top
   
 Post subject: Re: rolling the arches
PostPosted:Wed May 22, 2013 4:49 pm 
Offline
Big Block
User avatar

Joined:Thu Jul 10, 2008 10:41 am
Posts:827
Car Details:1968 Camaro Racing Car "Butch"
1968 Camaro Convertible 327"Camilla"
1979 AMC CJ7 Jeep 360V8
1980 BMW E21 Alpina B6 2.8
1991 BMW E30 HartgeH26
1958 as yet unrevealed sportsracer with chevV8
Location:Isle of Man and Inverness
I agree- much better getting wheels that fit!

Camaro Wheels
Classic Industries produce a 15X 8" rally wheel with 4.5" backspacing-this enables the wheels to fit all Camaros 67-72, Chevelle 64-72 and Nova 64-72
The original came with 4" backspacing
Global West recommend the following:
67-69 Camaro 16 X 8" wheel with 5" backspacing in conjunction with 245x50 x 16 tyres
Friend Runs 8.5" X 16 Image wheels with 4" backspacing

I have a set of 10x15 new unused Revolutions that will not fit Butch because it is lowered!

In extremis we have used the trolley handle to splay the wheelarch slightly rolling it under the arch over the tyre! (After an accident).

I am pretty sure a set of 275 50 15 will fit the back (on 8x15) no idea if these will fit the front! Will find out before September!

Certainly 255 60 15 will fit on the above wheels - you need 4.5 inch backspacing

_________________
Kind Regards
TopCat
Secretary
Classic Camaro Club
Member of The Association of American Car Clubs UK
Email :tboles@strathnoon.co.uk Websites: http://www.classiccamaroclubuk.com and:
http://www.youtube.com/watch?v=IdhLJtR_ZY4


Top
   
 Post subject: Re: rolling the arches
PostPosted:Wed May 22, 2013 5:03 pm 
Offline
Big Block
User avatar

Joined:Thu Jul 10, 2008 10:41 am
Posts:827
Car Details:1968 Camaro Racing Car "Butch"
1968 Camaro Convertible 327"Camilla"
1979 AMC CJ7 Jeep 360V8
1980 BMW E21 Alpina B6 2.8
1991 BMW E30 HartgeH26
1958 as yet unrevealed sportsracer with chevV8
Location:Isle of Man and Inverness
[img]59577851@N03/8169259418/in/photostream/[/img]

http://www.flickr.com/photos/59577851@N ... otostream/
I have a spare set of 5 spoke Camaro wheels 7x15 if they are any good for you?
see above

_________________
Kind Regards
TopCat
Secretary
Classic Camaro Club
Member of The Association of American Car Clubs UK
Email :tboles@strathnoon.co.uk Websites: http://www.classiccamaroclubuk.com and:
http://www.youtube.com/watch?v=IdhLJtR_ZY4


Top
   
 Post subject: Re: rolling the arches
PostPosted:Wed May 22, 2013 5:20 pm 
Offline
Big Block
User avatar

Joined:Wed Aug 01, 2012 10:49 pm
Posts:500
Car Details:a car thats older than the c*** that drives it....
Location:n london/ herts
cheers Top cat for the info ....keep changing my mind on wheels ....3 times this week and now want 17" polished torque thrust ...all i know is i hate slot mags and just wish someone stocked wheels and i could try them on the car for looks and fitment....
Attachment:
ARE-1097861_ml.jpg
ARE-1097861_ml.jpg [11.6KiB |Viewed 945 times ]


Top
   
 Post subject: Re: rolling the arches
PostPosted:Wed May 22, 2013 5:36 pm 
Offline
Big Block
User avatar

Joined:Thu Jul 10, 2008 10:41 am
Posts:827
Car Details:1968 Camaro Racing Car "Butch"
1968 Camaro Convertible 327"Camilla"
1979 AMC CJ7 Jeep 360V8
1980 BMW E21 Alpina B6 2.8
1991 BMW E30 HartgeH26
1958 as yet unrevealed sportsracer with chevV8
Location:Isle of Man and Inverness
North Hants Tyres have stacks of wheel options!

my Flickr website has all changed - now I can't add URLs to a forum!

_________________
Kind Regards
TopCat
Secretary
Classic Camaro Club
Member of The Association of American Car Clubs UK
Email :tboles@strathnoon.co.uk Websites: http://www.classiccamaroclubuk.com and:
http://www.youtube.com/watch?v=IdhLJtR_ZY4


Top
   
 Post subject: Re: rolling the arches
PostPosted:Wed May 22, 2013 5:39 pm 
Offline
Big Block
User avatar

Joined:Wed Aug 01, 2012 10:49 pm
Posts:500
Car Details:a car thats older than the c*** that drives it....
Location:n london/ herts
tried them..... all the ones i like they have to get imported in :thumbdown:


Top
   
 Post subject: Re: rolling the arches
PostPosted:Wed May 22, 2013 8:49 pm 
Offline
Big Block
User avatar

Joined:Fri Mar 19, 2010 1:35 am
Posts:2566
Car Details:79' camaro road & track day toy. 383 stroker, 5 speed TKO trans, lots of suspension stuff, 13" Vette brakes, 18" wheels.
Location:Luton
Didn't there used to be a baseball bat against the tyre technique... ? :D

_________________
“You only live once, but if you do it right, once is enough.”


Top
   
Display posts from previous: Sort by 
Post new topic Reply to topic  [12 posts ]  Go to page12Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 167 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Limited