Hi Russ,
Do you mean this bit?
| Attachments: |
| CDP-1.jpg [6.94KiB |Viewed 1425 times ] |
| The Camaro Club (UK) http://classiccamaroclub.mfatw.com/ |
|
| 67 First Gen - Dashboard removel - advice please. http://classiccamaroclub.mfatw.com/viewtopic.php?f=9&t=1932 |
Page 1 of 1 |
| Author: | Russ D [Tue Aug 23, 2011 6:34 am ] |
| Post subject: | 67 First Gen - Dashboard removel - advice please. |
Ive a 67 and as usual, im on here begging for info. I need to get the black facia off the dash centre panel to get it out, now I can feel the screws that secure the panel in but they're under the black facia and i just can't figure out how to get it off to get to the screws behind it. The aftermarket radio is secured in from the back of the balck facia and ive a problem with it and need to get it out. Its fitted under the heater controls. Anyone know how it's done withot trashing it please? Thanks. Russ. |
|
| Author: | mark68 [Tue Aug 23, 2011 9:27 am ] | ||
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. | ||
Hi Russ, Do you mean this bit?
|
|||
| Author: | Russ D [Tue Aug 23, 2011 2:11 pm ] |
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. |
Thats the boy, how does it come out? Just to the right of the middle hole with the curved top under the black panel theres a screw head, how do you get to them? |
|
| Author: | mark68 [Tue Aug 23, 2011 3:08 pm ] |
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. |
IF I remember correctly, someone had fixed that panel with 4 self tappers, much to my disgust! and the rest of it looked like it had some sort of glue (long since perished). So removing it was easy enough. I'm at work, so can't check, I have the panel at home. If I find anything obvious, then I will post again. |
|
| Author: | Russ D [Tue Aug 23, 2011 3:28 pm ] |
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. |
Thanks v much, got me flumuxed that (nothing unusual there) Ive found the three screws in the bottom where it curves down and under past the ash tray. The rest seem to be under the black cover. Cheers for the help Mark. |
|
| Author: | wanderingkurt [Tue Aug 23, 2011 10:15 pm ] |
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. |
Hi Russ, after removing the screws at the lower edge, you need to move the panel away from the dash, starting at the bottom, then lift it up. The panel is clipped into a retainer at the top. I have scanned the relevant page out of my factory assembly instruction manual but cant figure out how to attach it here. Hope this helps, Kurt |
|
| Author: | Russ D [Wed Aug 24, 2011 6:13 am ] |
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. |
Got it, managed to remove it in tact and un damaged, thanks chaps. Russ. |
|
| Author: | wanderingkurt [Tue Aug 30, 2011 8:43 pm ] | ||
| Post subject: | Re: 67 First Gen - Dashboard removel - advice please. | ||
think i just worked out how to attach an image. i know this problem has been solved but i thought i'd up load it for future reference, the centre trim (5) is clipped into the top bracket (4) as in attached image kurt
|
|||
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|