| The Camaro Club (UK) http://classiccamaroclub.mfatw.com/ |
|
| Exhaust Diameter http://classiccamaroclub.mfatw.com/viewtopic.php?f=6&t=3701 |
Page 1 of 2 |
| Author: | FerdiZ28 [Mon Feb 03, 2014 7:11 pm ] |
| Post subject: | Exhaust Diameter |
Evening chaps Does ayone know for sure the standard exhaust diameter for my 98 (LS1)? I am about to order an exhaust cut off valve and wondered which one to ask for. Also, spinnybits (posts here occasionally) would like to know the answer to the above question only for his 97 TA (LT1)? We have been under the cars and measured roughly and it seems it could be 3", but I'm reading elsewhere that it could be either that, 2.5" or even 2.75". Cheers, Ferdi |
|
| Author: | 3rdGenmalc [Mon Feb 03, 2014 9:10 pm ] |
| Post subject: | Re: Exhaust Diameter |
How are you measuring, with a rule or calipers ? You´ll never eyeball it with a rule so............ Circumference = Pi x Diameter. 3" x 3.142 = 9.426", circumference.....so measure the circumference. 2.5" x 3,142 = 7.855" 2.75" x 3.142 = 8.64" |
|
| Author: | chevy-stu [Wed Feb 05, 2014 3:21 pm ] |
| Post subject: | Re: Exhaust Diameter |
|
|
|
| Author: | FerdiZ28 [Thu Feb 06, 2014 5:03 pm ] |
| Post subject: | Re: Exhaust Diameter |
Hehe That's the look I'm after. Theers for the Maths reminder, bought some calipers and shall measure at the weekend. Anyone fitted an electronic cut off to the exhaust? Thinking pre-cat. I'll tell everyone it is for the perfomance increase but its really for the noise 
|
|
| Author: | chevy-stu [Thu Feb 06, 2014 10:17 pm ] |
| Post subject: | Re: Exhaust Diameter |
I've got twin electric cutouts on mine... y pipe and units direct from a US companycalled Badlanz. Had them built intothenew exhaust about 4 or more years ago. worked fine for a while then one stripped the gears. Badlanz did replace it for free, but I had to post broken one back.then one motor went atabout 12 months, free replacement again.. the bolts constantly work loose on the flap and control rod and need tightening at least annually.. I've got one removed atthemoment as one flap broke in half at Xmas... |
|
| Author: | FerdiZ28 [Fri Feb 07, 2014 8:52 am ] |
| Post subject: | Re: Exhaust Diameter |
Cheers for that, do you notice any difference in throttle response? Sounds like you haven't had much luck with yours. I've been speaking to this fella on ebay, if his prompt communication is anything to go by it seems like a legit product. http://www.ebay.co.uk/itm/350803970129? ... 1423.l2649 Just need to know what size pipe but I'll put some calipers against it this weekend. Cheers! |
|
| Author: | FerdiZ28 [Fri Feb 07, 2014 9:21 am ] |
| Post subject: | Re: Exhaust Diameter |
Cheers for that, do you notice any difference in throttle response? Sounds like you haven't had much luck with yours. I've been speaking to this fella on ebay, if his prompt communication is anything to go by it seems like a legit product. http://www.ebay.co.uk/itm/350803970129? ... 1423.l2649 Just need to know what size pipe but I'll put some calipers against it this weekend. Cheers! |
|
| Author: | chevy-stu [Sat Feb 08, 2014 12:47 pm ] |
| Post subject: | Re: Exhaust Diameter |
It definately increaes power. I had my car dyno'd on a rolling road, and first time it showed nearly 20hp more with the valves open, and second time, after the engine rebuild a little over 5hp more. The main thing is the noise of course  I think by the nature of cutout valves, they sit in a very dirty, exposed vibration prone part of the the car, so failure in my case wasn't too suprising. QTP was one of the better makes I've heard, but I bought the Badlanz as they had good reviews but were a little cheaper. There was another type with a sliding valve rather ran rotating called 'Dougs' that looks like it might be more reliable and seal better.. |
|
| Author: | z28stu [Sun Feb 09, 2014 10:25 am ] |
| Post subject: | Re: Exhaust Diameter |
Ive been thinking about the ol exhaust cut out since i bought my z28 but just havent got round to getting one yet Is it just me or does the ebay pic make it look cheap and quite chunky ??? Ive always liked the QTP stuff....  http://quicktimeperformance.com/QTEC/ Ferdi if you do go for it post some pics up for us
|
|
| Author: | 3rdGenmalc [Sun Feb 09, 2014 10:32 am ] |
| Post subject: | Re: Exhaust Diameter |
Search Summit, http://www.summitracing.com/dom/search/ ... =Ascending Even cable operated, http://www.summitracing.com/dom/parts/m ... /overview/ S´only 2" diameter though. 
|
|
| Page 1 of 2 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|