The Camaro Club (UK)
http://classiccamaroclub.mfatw.com/

69 Camaro fron sheet metal to go
http://classiccamaroclub.mfatw.com/viewtopic.php?f=15&t=4502		 Page 1 of 2
Author:  raven68 [Fri May 22, 2015 8:02 am ]
Post subject:  69 Camaro fron sheet metal to go
Got the old front sheet metal off my 69 Camaro staking up too much space and it will go to the metal recycler in the next week or two.
So does anyone want the following before its scrapped? Don't want anything for the pieces but all to go in one lot please.

Pair of front wings - damaged and filled see pic below of the drivers side - passenger side similar hence I ordered new ones as not got the panel beating skills to save them but some one may fancy a go ??
Valance panel
Top nose panel
Scuttle vent panel

Front drivers wing as below ....

Image
Author:  Benji [Tue Nov 17, 2015 2:36 am ]
Post subject:  Re: 69 Camaro fron sheet metal to go
Do you still have any of these parts?

Cheers,
Ben
Author:  raven68 [Tue Nov 17, 2015 7:42 am ]
Post subject:  Re: 69 Camaro fron sheet metal to go
Quote:
Do you still have any of these parts?

Cheers,
Ben
Yes, as usual never got round to having the clear out !! Also got the pair of old doors that can go......... I'll be up the garage today and will check with regard to the front valence panel as I'm not sure we still have that piece. I'll reply again tonight. :thumbup:
Author:  Benji [Tue Nov 17, 2015 8:34 am ]
Post subject:  Re: 69 Camaro fron sheet metal to go
The valance panel was the main piece I needed too. Just my luck.

Let me know either way. Where abouts in the UK are you?
Author:  raven68 [Tue Nov 17, 2015 6:13 pm ]
Post subject:  Re: 69 Camaro fron sheet metal to go
Quote:
The valance panel was the main piece I needed too. Just my luck.

Let me know either way. Where abouts in the UK are you?
Checked and yes I do have the front lower valance panel ! I'm in Bristol.

In case others are interested the following panels are still available free of charge if anyone can make use of them

Pair of front wings - ideally need panel beating rather than 1/2" of filler on the front lower corners!
Pair of door shells
Bootlid - needs repair to both rear corners
Scuttle vent panel
Header panel above the grille
Author:  Benji [Tue Nov 17, 2015 6:38 pm ]
Post subject:  Re: 69 Camaro fron sheet metal to go
I will see how much it will cost to courier up to Durham, but thanks for the offer. Really appreciate it!
Author:  Benji [Tue Nov 24, 2015 8:35 pm ]
Post subject:  Re: 69 Camaro fron sheet metal to go
I'm struggling to find a way to transport the panel up. If anyone else wants it just let them take it. Thanks anyway.
Author:  Jamieg285 [Wed Nov 25, 2015 12:53 pm ]
Post subject:  Re: 69 Camaro fron sheet metal to go
Try uShip.com

I got a great deal for sending some quarter panels.
Author:  78 Camaro [Wed Nov 25, 2015 1:57 pm ]
Post subject:  Re: 69 Camaro fron sheet metal to go
I used Shiply couriers recently and they delivered a front wing from about 150 miles away for about £40 https://www.shiply.com/

https://www.parcel2go.com/?gclid=CID-nL ... wwodWQcFew is also a good website, it's a price comparison site for the majors i.e. parcel force.
Author:  raven68 [Wed Nov 25, 2015 8:16 pm ]
Post subject:  Re: 69 Camaro fron sheet metal to go
Quote:
I'm struggling to find a way to transport the panel up. If anyone else wants it just let them take it. Thanks anyway.
OK Benji, no worries mate. Ideally you need the weight and overall size to get a correct courier and its never going to be cheap cheap !
Page 1 of 2 All times are UTC
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/