| The Camaro Club (UK) http://classiccamaroclub.mfatw.com/ |
|
| Gen 3 Questions http://classiccamaroclub.mfatw.com/viewtopic.php?f=1&t=2250 |
Page 1 of 1 |
| Author: | neil.w [Thu Apr 19, 2012 9:33 pm ] |
| Post subject: | Gen 3 Questions |
Hi guys could any one tell me where you can get the front Camaro emblem called Header panel emblem best price  ,also on the rear hatch/tailgate on the inside between the glass and metal panel what covers the transition point mine had a piece of black plastic glued on ,only one side  also if you lift it up mine has two holes drilled in the side just below the spoiler bolt on both sides any one tell me whats missing ? hope you can help Cheers Neil 
|
|
| Author: | chevy-stu [Fri Apr 20, 2012 12:04 pm ] |
| Post subject: | Re: Gen 3 Questions |
I think I've bought emblems in the past from NPD and US ebay.. Has Rocky got any S/H ones ? |
|
| Author: | camaro85iroc [Fri Apr 20, 2012 12:13 pm ] | |||
| Post subject: | Re: Gen 3 Questions | |||
this what your after  http://www.ebay.co.uk/itm/1986-7-Camaro ... 1c251d7201 or this  http://www.ebay.co.uk/itm/1986-7-Camaro ... 1c2620800b
|
||||
| Author: | neil.w [Sat Apr 21, 2012 12:25 am ] |
| Post subject: | Re: Gen 3 Questions |
Thanks for the info guys spot on  any of you third gen guys help with the inside rear hatch/tailgate problem any pics ? once again Cheers Neil P.S. the 89 Camaro isn,t old enough ? for N.P.D
|
|
| Author: | Rocky [Tue Apr 24, 2012 8:42 pm ] |
| Post subject: | Re: Gen 3 Questions |
I think I have a good secondhand one, I might have a brand new GM one but they are quite expensive for original. |
|
| Author: | neil.w [Tue Apr 24, 2012 10:51 pm ] |
| Post subject: | Re: Gen 3 Questions |
Hi Rocky how good is the second hand one is it good enough to go with new paint ?if not what kind of price is the other one ,also any ideas on how the rear glass to metal panel inside of the hatch is covered (most is covered with big trim panel )just the end sections mine was mainly black silicone and on one end a piece of black plastic Cheers Neil.
|
|
| Author: | Rocky [Wed Apr 25, 2012 8:28 pm ] |
| Post subject: | Re: Gen 3 Questions |
Will get some pics for you I have a couple of different ones. There is a plastic cover that goes on the inside of tailgate the plastic bits either side are just to cover the join. Are you planning on splitting the deck lid from the glass as its quite involved. |
|
| Author: | neil.w [Wed Apr 25, 2012 11:02 pm ] |
| Post subject: | Re: Gen 3 Questions |
I took the tailgate off to clean up the inside and the gutter before paint ,the metal part was out of line i managed to slacken the nuts and tap it back (with the rams off ) and tighten up the nuts ,quite lucky i think but it seems to have worked ,on the inside there was only one plastic piece and loads of black silicone it didnt look factory .Cheers mate sort some prices out Neil
|
|
| Author: | Rocky [Thu Apr 26, 2012 8:28 pm ] |
| Post subject: | Re: Gen 3 Questions |
Pmed ya |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|